Operator Reference

HALCON Operator Reference / Calibration / Multi-View
ClassesClasses | | Operators

deserialize_calib_dataT_deserialize_calib_dataDeserializeCalibDataDeserializeCalibDatadeserialize_calib_data (Operator)

deserialize_calib_dataT_deserialize_calib_dataDeserializeCalibDataDeserializeCalibDatadeserialize_calib_data — Deserialize a serialized calibration data model.

Signature

deserialize_calib_data( : : SerializedItemHandle : CalibDataID)

Herror T_deserialize_calib_data(const Htuple SerializedItemHandle, Htuple* CalibDataID)

void DeserializeCalibData(const HTuple& SerializedItemHandle, HTuple* CalibDataID)

void HCalibData::DeserializeCalibData(const HSerializedItem& SerializedItemHandle)

static void HOperatorSet.DeserializeCalibData(HTuple serializedItemHandle, out HTuple calibDataID)

void HCalibData.DeserializeCalibData(HSerializedItem serializedItemHandle)

def deserialize_calib_data(serialized_item_handle: HHandle) -> HHandle

Description

deserialize_calib_datadeserialize_calib_dataDeserializeCalibDataDeserializeCalibDatadeserialize_calib_data deserializes a calibration data model, that was serialized by serialize_calib_dataserialize_calib_dataSerializeCalibDataSerializeCalibDataserialize_calib_data (see fwrite_serialized_itemfwrite_serialized_itemFwriteSerializedItemFwriteSerializedItemfwrite_serialized_item for an introduction of the basic principle of serialization). The serialized calibration data model is defined by the handle SerializedItemHandleSerializedItemHandleSerializedItemHandleserializedItemHandleserialized_item_handle. The deserialized values are stored in an automatically created calibration data model with the handle CalibDataIDCalibDataIDCalibDataIDcalibDataIDcalib_data_id.

Note that serialize_calib_dataserialize_calib_dataSerializeCalibDataSerializeCalibDataserialize_calib_data does not serialize any calibration results. Yet, calibrate_camerascalibrate_camerasCalibrateCamerasCalibrateCamerascalibrate_cameras can be called for a fully configured calibration model immediately after the deserialization. All calibration results are accessible afterwards.

Execution Information

  • Multithreading type: reentrant (runs in parallel with non-exclusive operators).
  • Multithreading scope: global (may be called from any thread).
  • Processed without parallelization.

Parameters

SerializedItemHandleSerializedItemHandleSerializedItemHandleserializedItemHandleserialized_item_handle (input_control)  serialized_item → HSerializedItem, HTupleHHandleHTupleHtuple (handle) (IntPtr) (HHandle) (handle)

Handle of the serialized item.

CalibDataIDCalibDataIDCalibDataIDcalibDataIDcalib_data_id (output_control)  calib_data → HCalibData, HTupleHHandleHTupleHtuple (handle) (IntPtr) (HHandle) (handle)

Handle of a calibration data model.

Result

If the parameters are valid, the operator deserialize_calib_datadeserialize_calib_dataDeserializeCalibDataDeserializeCalibDatadeserialize_calib_data returns the value 2 ( H_MSG_TRUE) . If necessary, an exception is raised.

Possible Predecessors

fread_serialized_itemfread_serialized_itemFreadSerializedItemFreadSerializedItemfread_serialized_item, receive_serialized_itemreceive_serialized_itemReceiveSerializedItemReceiveSerializedItemreceive_serialized_item, serialize_calib_dataserialize_calib_dataSerializeCalibDataSerializeCalibDataserialize_calib_data

Module

Calibration

ClassesClasses | | Operators